Sometimes, dust builds up on the inside of your speaker and you don’t want to just borrow a pair of gloves. You can use this guide to make some cheap caps that will keep the dust out while allowing sound through.
The “best speaker brands” is a question that many people have been asking. The answer to the question is simple, you can make your own speaker dust caps.
We earn money from qualifying purchases made on our website as an Amazon Associate.
To protect their diaphragms from damage, dirt, and debris, several speaker types feature a dust cover in front of them. In most situations, new dust caps for popular speaker types are not available. You may, however, create a dust cover out of paper or rubber using very simple tools and supplies.
The speaker will ultimately get blocked and cease operating if there is no dust cover. Fortunately, making your own speaker dust caps is straightforward and requires just a few basic components.
- a piece of paper (notebook paper works fine)
- Stamp pad made of rubber (any ink will work)
Step 1: On the paper, draw circles.
On a piece of paper, draw two circles large enough to accommodate your diaphragm. The inner border of the speaker’s housing is normally approximately an inch away from the speaker’s diameter.
Step 2: Make a slit in the middle of the two circles.
Draw a slit between the two circles with the pencil and ruler, going all the way through each so you get a line separating each circle into four sections.
Ensure that the divide is a vertical line. This will come in in while we’re cutting out our new dust cover.
Step 3: Cut The Circle Out Of The Paper
Along with the division you just made in step two, cut off the paper circle. The divide should make it simpler to create clean, even cuts by allowing you to cut perfectly around both circles at the same time. To make clean, straight cuts, you may wish to use the ruler once more.
Step 4: Fill the Rubber Stamp Pad with Ink
Fill your rubber stamp pad with ink and gently coat the two paper pieces with it.
Make sure you don’t ink up more than a quarter of each circle, since this will make it difficult to place them afterwards. If you think it’s necessary, apply a couple coats for even coverage. Allow to dry.
Step 5: Take out the screws that hold the diaphragm in place.
Remove any screws that hold down the diaphragm or keep the ring in place on your speaker and ready it to receive its new dust cap.
These screws should be kept secure since they will be reused when the dust cap is reinstalled after testing.
Step 6: Place the Paper Dust Caps in Place
Replace the freshly-inked, dried paper dust caps in the speaker and then remove them. The ink should have transferred to the diaphragm by now. This indicates that your headgear is ready to wear.
Step 7: Replace the Diaphragm in Your Speaker
If you removed your speaker’s diaphragm and screws/nuts during this method, replace them. Make sure all of the pieces are in place so you can test the sound afterwards.
Methods for Making Your Own Speaker Dust Cap
You may create your speaker dust caps in a variety of ways. Let’s look at three typical approaches.
Using a Piece of Cloth (method 1)
The first technique involves using a piece of fabric. You’ll need a piece of fabric that’s bigger than the dust cap itself to achieve this.
Sew the edges of the dust cap together after cutting out the form. Make sure the cloth is thick enough to avoid tearing or leaking sound.
Using Foam Rubber as a Second Method
The second technique involves the use of foam rubber. If you need a dust cover that is lightweight and portable, this is a wonderful choice.
Cut out a piece of foam rubber the same size as the dust cap and adhere it on the speaker using a hot glue gun. Alternatively, you may use specialist speaker dust cap glue.
Method 3: Using a Plastic Piece
A piece of plastic may be used as the third approach. If you want a dust cap that is both robust and waterproof, this is a wonderful choice.
Cut out a piece of plastic the same size as the dust cap and adhere it on the speaker using a hot glue gun.
The Methods Listed Above Can Be Divided Into Two Types:
1. Punching Techniques
The rolling approach increases the cap’s rigidity, enabling lower frequencies to be regulated more effectively, resulting in fewer slaps, thumps, and rattles.
The disadvantage is that it boosts the higher frequency range as well. This makes range compression or equalization, if necessary, significantly more difficult to regulate.
As a result, more caution should be used while using this sort of cap for drivers that demand a lot of low-end assistance while simultaneously requiring some high-end boost. Tweeters and tiny woofers, for example. Another disadvantage is that if not done correctly, it might twist off the driver’s cone.
2. The Method of Rolling
Punching is a very basic and straightforward technique of creating a dust cap. It doesn’t give the hat much firmness, but it helps keep the cloth from wrinkling.
The disadvantage is that it is readily damaged by a sharp item without any reinforcing.
The Advantages of Making a Speaker Dust Cap
1. You Have the Option to Customize the Dust Cap
The ability to modify them to match your room’s décor is perhaps the most apparent advantage. If you have a really distinctive or eclectic style, this is extremely vital.
2. You are able to save money
Another significant advantage of producing your own dust caps is the cost savings. Dust caps may be made for free using materials you already have on hand.
If you need to buy some materials, they will most likely be inexpensive.
3. You Have the Option to Customize Your Audio Experience
You may also customize your audio experience by making your own speaker dust covers. Dust caps may be customized in terms of form, size, and color to ensure that they match your speakers precisely.
This degree of personalization may make listening to music, viewing movies, or playing video games a pleasurable experience for all members of your family.
4. They’re Simple to Make
Another advantage of manufacturing your own dust caps is that they are simple to produce. You can make them with minimal effort if you have the necessary tools and are ready to put in some time.
5. Customizable Size, Shape, Color, and Material
The flexibility to customize your size, shape, color, and even material may improve your listening experience significantly.
This is one option that may be ideal for you if you want an interesting method to decorate the inside of your house without breaking the budget.
Regardless of whatever technique you choose, be sure to take your time and be cautious while building your dust cap. It’s critical to get it perfect if you want to get the finest sound quality out of your speaker.
All of these techniques are simple to use and will aid in the protection of your speaker against dust and moisture. Start by selecting the approach that best matches your requirements.
Watch This Video-
Frequently Asked Questions
How do you make speaker dust covers?
A: Depending on how much you want to cover up, use a dust mask or paintbrush and dab the dust off with water.
Are speaker dust caps necessary?
Does dust cap affect sound?
A: Dust caps are not good for sound quality.
- best speakers for music
- best door speakers